Ten elements of colloid mill installation operation 1. The vibration of this machine is small when working, so it is not necessary to lay the foundation. It is best to pad a rubber sheet. 2. The electrical installation of the motor should be equipped with an automatic switch for overload and short-circuit protection matching with the motor power, and the ground wire should be connected. 3. For the maintenance and use of the motor, please refer to the operating instructions of the motor. 4. To verify the factory delivery at 0: 00, first loosen the two handles on the clearance adjustment sleeve, hold the handles clockwise (in a thin direction) and turn the adjustment sleeve until it can't turn. At this time, use a random wrench to turn it counterclockwise, because the fixed bolt on the rotating tooth is reversed, and the rotating tooth can't turn. This is because the rotating tooth of the grinding tooth is in close contact with the fixed tooth without clearance. Then turn the clearance adjusting sleeve counterclockwise (in the coarse direction), while turning the rotating teeth with a wrench, until there is a heavy friction sound between the rotating teeth and the fixed teeth, and then it becomes a light friction sound, and the 0 point on the mediation sleeve just corresponds to the scale on the dial, which is 0 point. At this time, the clearance between the rotating teeth and the fixed teeth of the grinding teeth is the minimum allowable clearance. Generally, the motor can be started only after the clearance is enlarged by five grids (in the coarse direction). 5. Check the rotation direction of the motor: use a random wrench to determine that the rotating stator teeth are not in contact and then start the motor, which should be rotated clockwise. 6. Rotate the adjusting sleeve, and do a material crushing test under different clearances of the rotating teeth to find out the best clearance suitable for the requirements. After each clearance adjustment, tighten the handle and lock the adjusting sleeve. 7, adjust the gap must be adjusted when the motor is not started, it is forbidden to adjust the gap when the motor rotates. When the motor is started, it must be ensured that there is no friction between the rotor and stator teeth to avoid damaging the rotor and motor. 8. In order to ensure that the shaft seal (screw seal or mechanical seal) works well and does not leak, remember to start the machine before feeding, and turn it off when the material is discharged. Seal leakage should be maintained or replaced in time. 9. At the end of each day's work, clean the grinding cavity with water when the machine is turned on, and stop the machine only after it is completely drained, so as to ensure that the grinding teeth can be well crushed when the machine is turned on, and the grinding teeth will not be stuck by the residual materials. 10, motor bearing should add lubricating oil once every six months. There should be no hard point objects such as metal objects and stones in the processing materials to avoid damaging the grinding teeth or suppressing the motor. If it is stopped for a long time, the grinding cavity should be cleaned and dried. Six technical advantages of stainless steel colloid mill Working principle of stainless steel colloid mill: the basic principle is to connect the fixed teeth and the moving teeth at high speed. Except for the motor and some parts, all parts in contact with the material are made of high-strength stainless steel. Especially, the key dynamic and static grinding discs are strengthened, so they have good corrosion resistance and wear resistance, which makes the processed materials pollution-free, hygienic and pure. Technical advantages of stainless steel colloid mill: 1. Only the valve is switched, and the pump and mill run continuously, thus truly realizing uninterrupted production. 2. It can be customized according to users' needs. All models are reserved with external interfaces, which can expand their functions and output, and can be used for fixed factory production or mobile on-site production. 3. There are two control modes: manual/automatic integration and manual control. 4. It can produce ultra-high content of modified emulsified asphalt (SBS content ≥4%, asphalt content ≥65%). Colloidal mill performance Haoxing colloid mill has the characteristics of compact design, utility model, beautiful appearance, good sealing, stable performance, convenient operation, simple decoration, durability, wide application range and high production efficiency. It is the most ideal processing equipment for handling fine υ materials. With the exception of motors and some parts, all parts of Haoxing colloid mill products that come into contact with materials are made of high-strength stainless steel 304, 316, 316L, 2205 and alloy steel. In particular, the key dynamic and static grinding discs are strengthened. Therefore, it has good corrosion resistance and wear resistance, which makes the processed materials pollution-free, hygienic and pure, and can also be customized according to the special requirements of users.